AI8 LAB · v nastajanju ↗
BD × AI Lab

HORIZONTAL TROMPE HYBRID

Multi-Channel River & Ocean Energy Harvesting System
Origin: A dream about a boat travelling faster than river current, propelled only by internal tube geometry compressing air-water mixture. Morning analysis revealed connections to DGTE (low-temperature heat engine), MDL (information compression), and the trompe (historical hydraulic air compressor). The horizontal-current version remains a research hypothesis; novelty requires a documented prior-art search.
3
Energy Sources
15
Channels
0
Submerged moving parts in proposed core
30+
Year design target, untested

LAB REVIEW · 26 OCT 2026

The chapters below preserve BD’s original hypothesis and illustrative simulator results. They are not field measurements. The present gate is a same-site, same-flow comparison with a conventional micro-hydro turbine or a hydrokinetic rotor. Measure flow, upstream and downstream hydraulic head, intake drag, loaded air pressure and airflow, and net electrical output. Record construction and maintenance cost on the same service-life basis.

Energy boundary: river-current power crossing capture area A is at most ½ρAv³ before conversion losses; pressure at depth is not by itself a renewable power source. At v = 0.5 m/s, the ideal flux is about 62.5 W/m², so 2 kW from current alone requires more than 32 m² of capture area before losses. A buried separator needs a sustained pressure/head difference and a recovery path for water and compressed air. The 2 kW, zero-maintenance, 39% TCO, threshold and novelty claims below are unverified targets.

First falsifier: a transparent loop with metered Q, ΔH, air mass flow and loaded p–V work. If measured net pneumatic or electrical output, including pumping and re-priming, does not exceed uncertainty and a matched conventional device under the same flow/head, stop the performance claim. Entrained bubbles alone are not a pass.

CURRENT ARENA STATUS · v0.7a

HTH / trompe / pressure is currently the strongest low-cost physical kill-test branch. DGTE Arena v0.7a ranks the transparent HTH / trompe channel first: minimum clear-pipe velocity ramp, separator pressure, loaded airflow, deep-pool/polyline emulator, and debris/fouling pass.

First build: transparent channel with flow velocity, entrainment threshold, bubble survival, separator pressure, air-flow rate, water head/depth, and net pneumatic output. If it fails, salvage Venturi/degas data for DGTE carry-over and MGHB inlet tests.

See the current bench planner: MDLxDCC-Arena-DGTE.html.

ABSTRACT

This paper introduces the Horizontal Trompe Hybrid (HTH) — a passive hydraulic air compression architecture that harvests energy from river and ocean currents without moving parts. Unlike classical trompes which require vertical waterfalls or dams, HTH uses a funnel-Venturi intake to entrain air into horizontal or diagonal flow, combining three energy sources in a single system: kinetic current velocity, hydrostatic depth, and natural river gradient. An adaptive polyline pipe layout follows local topography rather than imposing fixed geometry, reading the river the way a mountaineer reads terrain.

A parametric simulator validates three fatal kill tests across all configurations: air entrainment occurs at velocities ≥0.5 m/s, bubbles survive transport to the separation chamber, and net energy is positive. Counterintuitively, deep slow pools produce more power than fast shallow sections — hydrostatic head dominates kinetic energy. A 200m adaptive polyline along a varied river profile yields ~2 kW continuous from standard HDPE pipes with zero maintenance.

The architecture extends to ocean environments (tidal currents, wave columns, OTEC coupling) and integrates with PV/DGTE solar-thermal hybrids. Economic analysis shows HTH costs 39% of micro-hydro turbine TCO at 30 years due to near-zero OPEX. No prior art describes a horizontal or terrain-adaptive trompe; the closest patent (WO2016046689A1, 2016) covers a related but distinct submerged compressor concept.

The founding hypothesis — compressibility correlates with quality — manifests literally: physical air compression directly measures energy extraction. HTH is the sixth independent domain confirmation of the MDL×DCC kernel after TSP, Sudoku, Chess, DNA, and NAS. The system that compresses best, harvests most.

1Founding Physics▸

1.1 Why Classical Trompe Requires Vertical Head

A classical trompe compresses air by entraining bubbles in falling water. The compression pressure equals the hydrostatic head: P = ρgh, where h is the vertical drop. No drop, no compression. All known trompe installations — from Catalan forges (1600s) through Ragged Chutes (1910) to modern mine-water treatment — require waterfalls, dams, or deep shafts.

1.2 Three Untapped Energy Sources in Horizontal Flow

A river flow can be described by velocity, pressure and elevation terms in one mechanical-energy balance. The following terms must not be added as three independent supplies without measuring upstream and downstream conditions:

  • Kinetic energy: E_k = ½mv². A river at 3 m/s has stagnation pressure ½ρv² ≈ 4.5 kPa.
  • Hydrostatic pressure: A 5 m water column has about 49 kPa gauge pressure at its base, but this does not yield continuous work without a sustained pressure difference, flow and return path.
  • River gradient: Rivers drop. A gradient of 0.5% over 100m gives 0.5m of additional head ≈ 4.9 kPa.

The original ~58 kPa sum is an illustrative pressure estimate, not available net head. Use measured total hydraulic energy at inlet and outlet, including intake and pipe losses, to establish what can be extracted continuously.

1.3 The Funnel-Venturi Principle

A submerged funnel facing upstream captures river flow across its full aperture area A_in and accelerates it through a constriction A_throat. By continuity: v_throat = v_river × (A_in / A_throat). At the throat, the Venturi effect creates a low-pressure zone that entrains air through ports above the waterline.

P_stagnation = ½ρv² = ½(1000)(3²) = 4500 Pa
v_throat = v_river × (A_in / A_throat)
Illustrative static pressure only: p_gauge = ρgh_depth. Net recoverable work needs measured Q·Δp across the whole system.

1.4 Thermodynamic Legitimacy

Unlike a perpetuum mobile, HTH has clearly identified external energy sources: gravitational potential energy driving river flow (ultimately solar-driven evaporation and rainfall) and solar heating of the water surface. No thermodynamic law is violated.

2River HTH System Architecture▸

2.1 Core Components

  1. Funnel-Venturi Intake: Submerged funnel oriented upstream, with Venturi throat and air ports above waterline.
  2. Downpipe Array: Pipes descending from throat to buried separation chamber. Multiple parallel pipes increase throughput.
  3. Separation Chamber: Buried below river bed. Air separates from water and collects under pressure.
  4. Compressed Air Reservoir & Discharge: Air storage with controlled release. Powers air turbine for electricity.
  5. Water Return: Outflow pipe exits downstream, using river gradient for additional driving force.

2.2 Additional Energy Channels

#ChannelMechanismNotes
1Kinetic (trompe)Funnel + Venturi + air entrainmentCore HTH
2HydrostaticDepth of separation chamber below surfaceCore HTH
3River gradientDownstream outflow at lower elevationCore HTH
4Thermal (DGTE)Solar-heated surface vs. cold depthRequires DGTE unit
5Vortex sheddingKármán vortices; piezo or linear inductionEven at low velocity
6Evaporative ΔTMoist air above river vs. ambientClimate-dependent
7Bypass turbineConventional rotary turbine on parallel pathGoverned split
8Air turbineCompressed air drives turbine at dischargeTime-shifted output

2.3 DCC-Style Channel Governance

The multi-channel architecture creates a resource allocation problem identical to DCC governance in TSP, NAS, and ChessDCC. A DCC controller monitors output from each channel and dynamically allocates flow. This is the same kernel operating in a new alphabet.

2.4 Adaptive Polyline Pipe — Reading the River

The distinction between "horizontal" and "vertical" trompe is a false binary. Real rivers have continuously varying profiles. The optimal HTH pipe layout is a polyline that adapts to local topography:

  • Fast shallow section → funnel/Venturi intake: maximum kinetic capture
  • Steep drop or cascade → diagonal/vertical pipe run: classical trompe physics
  • Deep pool (tolmun) → natural separation chamber: no excavation needed
  • Gentle glide → long diagonal run following riverbed gradient
  • Rocky step → vertical trompe segment: concentrated head gain

The pipe "reads" the river — it does not force a single geometry onto varied landscape. This is a TSP problem: find the path through candidate nodes that optimises total energy harvest minus installation cost.

Simulator discovery: deep slow pools (tolmun) produce MORE power than fast shallow sections. Depth dominates velocity. The MDL-optimal layout targets the deepest segments, not the fastest.
3Dimensioning: River Applications▸

3.1 Large Installation — Fast River Power Plant

LOOP review, 26 Oct 2026: The 24 m/s throat speed is a historical model value. For an ideal single-phase inlet accelerating from 3 to 24 m/s, the pressure drop is about 283.5 kPa. With atmospheric pressure 101 kPa, the throat would need to be at least 18.6 m below the surface merely to keep absolute pressure nonnegative. A throat at most 4 m deep cannot support the stated full-capture speed; its optimistic bound is about 17 m/s. The throat position, actual capture and two-phase losses are unknown. This does not by itself rule out an 8:1 geometric contraction at a lower flow.

Parameters: River velocity 3 m/s, depth 4m, gradient 0.3%, chamber buried 3m below riverbed.

ParameterValueUnit
Funnel aperture4 × 3m (W × H)
Contraction ratio8:1
Throat velocity24m/s
Hydrostatic head7m
Total pressure~76kPa
Downpipes (30cm ⌀)12–20pipes
Est. net output (30% eff.)~24kW
Annual output~210MWh/yr

3.2 Small Installation — Personal Use

Same-input check: At 1 m/s across 0.8 m², incoming kinetic flux is 400 W. A 133 W target would use 33% of that ideal flux; an unconstrained rotor of the same disk area has a Betz-model limit near 237 W. At 25 kPa gauge air pressure, 133 W of ideal isothermal pneumatic work requires at least about 6 L/s of air measured at ambient pressure; losses raise the requirement. The three Ø10 cm pipes total 0.0236 m², 8.5 times smaller than a 0.2 m² throat implied by 4:1 contraction of the 0.8 m² aperture. Neither flow nor air output has been measured.

Parameters: Stream velocity 1 m/s, depth 1.5m, gradient 1%, chamber buried 1m.

ParameterValueUnit
Funnel aperture1.0 × 0.8m
Contraction ratio4:1
Total pressure~25kPa
Downpipes (10cm ⌀)3pipes
Est. net output~133W
Annual output~1,161kWh/yr

133W continuous: enough for LED lighting, phone charging, small electronics, Wi-Fi router. For an off-grid cabin, this is meaningful.

3.3 Adaptive Polyline — River Profile Simulation

SegmentL(m)v(m/s)DepthNet(W)Pass?
Fast shallow riffle302.51.0114✓
Transition slope152.02.0298✓
Deep pool (tolmun)250.84.5410✓
Rocky cascade103.51.5245✓
Moderate glide401.52.5343✓
Steep drop83.02.0354✓
Lower pool200.74.00✗
Outflow glide501.22.0264✓
TOTAL1982,028
BD original framing: “Compressibility = quality: deeper compression → more energy. MDL in physics.” This is the originating hypothesis, not a measured relationship. Historical model result: the 0.8 m/s pool is assigned 410 W. If there is no usable surface drop or other source, even capturing all current kinetic energy would require at least 1.28 m³/s of water flow, or 1.6 m² of incoming current cross-section at 0.8 m/s, before losses. Actual capture is unknown. The lower pool has 0.7 m/s and 4.0 m depth but is marked FAIL; the page’s later blanket PASS threshold therefore lacks a stated condition. Depth can affect compression pressure and efficiency, but needs a measured energy input to produce power.
4Ocean HTH System Architecture▸

Ocean-Specific Energy Channels

#ChannelMechanismPotential
9Wave pressure oscillationCrest = overpressure, trough = underpressure. Natural pulsing.30–70 kW/m wavefront
10OWCSemi-submerged chamber, wave compresses air through turbine.Proven (Mutriku, Spain)
11Tidal currentPredictable bi-directional, 2–5 m/s. HTH funnel reverses.Very high (dense water)
12OTEC thermalSurface 25°C, 1000m depth 4°C. ΔT = 21°C. DGTE ideal.Theoretical TW-scale
13Salinity gradientRiver mouths: osmotic pressure. ~0.7 kWh/m³ freshwater.Niche but proven
14Wave vortexUnderwater cylinders, double Kármán vortices, piezo.Low power, zero maintenance
15Wave column trompeVertical pipe, wave raises water, compresses air at bottom.Elegant; no moving parts

Deployment Scenarios

Coastal Fixed Platform: Breakwater-mounted. Captures waves + tidal flow. Dual purpose: coastal protection + energy. Compressed air piped ashore.

Offshore Floating: Moored in strong current (Gulf Stream 1.5–2.5 m/s). HTH funnel beneath hull. Heave drives OWC. Autonomous power for offshore sensors.

Deep-Water OTEC + HTH: Full OTEC with HTH on cold-water intake pipe. Highest energy scenario.

5Dimensioning: Ocean Applications▸

5.1 Tidal Channel Installation

ParameterValueUnit
Funnel aperture (symmetric)5 × 5m
Tidal current3m/s (seawater)
Kinetic power (ρ=1025)~346kW
Compression pressure~200kPa (2 atm)
Est. net output (35% eff.)~120kW
Annual output (70% duty)~730MWh/yr

Key advantage: no moving parts underwater. Corrosion-resistant pipes, passive operation, maintenance only at surface-level air discharge.

5.2 Wave Column Trompe (Channel 15)

Vertical pipe anchored to seabed, open at top, sealed at bottom with air outlet. Wave crests raise water level, compressing trapped air. An array of 50 pipes along a breakwater: 25–100 kW with zero moving parts.

6PV/DGTE Integration▸

PV panels lose ~0.4%/°C efficiency above 25°C. A DGTE module beneath PV panels extracts waste heat, cooling the panel and generating additional electricity. Both systems benefit.

Combined efficiency from solar: ~25% vs. ~20% for standalone PV — 25% more electricity from the same surface area. The HTH/DGTE combination adds weather-independent baseload.

  • HTH: baseload power from river current (24/7)
  • PV: daytime solar electricity
  • DGTE on PV: waste heat recovery + panel cooling
  • DGTE on HTH: surface/depth thermal gradient
  • Compressed air storage: time-shifting to demand peaks
7Economics: HTH vs. Micro-Hydro▸

7.1 The MDL Principle

Each additional channel increases output but also cost. The optimal design is where marginal cost of the next channel exceeds its marginal return. MDL applied to engineering economics: the system that harvests the most with the least complexity wins.

7.2 Channel Hierarchy by ROI

TierChannelsAdded CAPEXMoving Parts
11+2+3 (core trompe)Base costZero
28 (air turbine)+15–20%One (dry, accessible)
37 (bypass turbine)+25–35%Turbine + valve
44 (DGTE thermal)+40–60%Pump (small)
55,6 (vortex, evap.)+20–30%Zero (piezo)
Tier 1+2 is the sweet spot: compressed air + electricity, zero underwater moving parts, air turbine at surface for easy maintenance.

7.3 Total Cost of Ownership: 100W Small Installation

PeriodHTH TCO (€)Micro-Hydro TCO (€)HTH Advantage
Year 0 (CAPEX)2,6002,500−€100
10-year3,0504,900+€1,850 (38%)
20-year3,6507,700+€4,050 (53%)
30-year4,20010,800+€6,600 (61%)

The historical table gives HTH at 39% of micro-hydro TCO at 30 years under its assumed cost entries. This is a scenario, not observed life-cycle cost; installation, cleaning, blockage, air handling and replacement costs need measured estimates for both designs.

7.4 The MDL Verdict

In the illustrative table, the turbine has €100 lower initial capital cost, while HTH has lower 10-year (€3,050 vs €4,900) and 30-year (€4,200 vs €10,800) totals. The original “turbine wins at 10 years” conclusion contradicted those inputs. No reliability advantage or cost ordering has been verified at equal delivered energy and service level.

8Cross-Domain Transfer — 8Z Kernel▸
ConceptTSPNASHTH
Sensors22+ geometricDrain, poly-fovea, scent15 energy channels
GovernanceMDL selects sensorsDCC on trajectoriesDCC allocates flow
ArenaTour quality (gap %)Val. accuracykWh output
CompressionMDL on tour structureMDL on arch. spacePhysical air + MDL on governance
BD proposes HTH as a sixth domain test of the MDL×DCC hypothesis. Air compression alone does not verify that cross-domain claim. Define a quality metric and compare adaptive governance with a fixed design under equal hydraulic inputs.
9Originality Assessment & Kill Tests▸

9.1 What Is Original

  1. Horizontal trompe: All known trompe literature from 1588 onward describes vertical devices. No publication describes a trompe driven by horizontal current velocity via funnel-Venturi intake.
  2. Adaptive polyline pipe: A pipe that follows river topography, switching between geometries. No precedent.
  3. Multi-channel on single passive infrastructure with DCC governance. Architecturally novel.
  4. MDL/TSP optimisation of pipe layout: Novel cross-domain transfer.

9.2 What Is NOT Original

The trompe itself (16th century). Venturi entrainment. OWC wave energy. OTEC. CAES. PV/thermal hybrids. The novelty is in the combination, geometry, and governance — not individual components.

The original note identifies WO2016046689A1 as related prior art. A claim of patentable novelty for the combination needs a claim-by-claim search and legal review; this lab has not established it.

9.3 Fatal Kill Tests

KT1 — Insufficient Venturi entrainment: If a funnel in 1–3 m/s flow cannot entrain enough air, the horizontal mechanism fails. This is THE question. TEST: transparent pipe in stream, visual confirmation.
KT2 — Bubble collapse: If bubbles are destroyed before reaching the chamber. TEST: measure air volume at chamber vs. air entrained.
KT3 — Net energy negative: At stable loaded operation, measure water flow Q, total hydraulic head across the complete device, air pressure and mass or volume flow, auxiliary consumption and uncertainty. Compare useful air or electric power to hydraulic input and a conventional device at the same site; chamber pressure alone cannot determine net power.

9.4 Simulator Verdict

The original simulator marks three model checks PASS at velocity ≥0.5 m/s and depth ≥1.5 m. Those marks depend on assumptions that have not been validated against measured entrainment, sustained head, hydraulic losses or loaded output. The model’s 100 W–66 kW range is a hypothesis, not a demonstrated output. A physical energy ledger is the next gate.

9.5 Confidence Assessment

ClaimConfidenceBasis
Concept is novel85%Literature search + patent check
Venturi entrains air at river velocity60%Physics supports; no empirical data for horizontal
Useful compression without vertical head alone40%4.5 kPa from velocity alone is very low
Hybrid (horizontal + diagonal + depth) viable70%Combines proven physics; nothing exotic
TCO advantage over turbines at 30yr80%Zero moving parts = near-zero OPEX
Small-scale (100W) practical55%Depends on KT1 and scaling laws
DCC governance adds value70%Proven in TSP/NAS/Chess
10Open Questions for AI8 Family▸
  1. Funnel geometry: optimal contraction ratio for maximising entrainment while minimising cavitation?
  2. Bubble dynamics: at >10 m/s throat velocity, do bubbles survive or collapse?
  3. Corrosion and biofouling in ocean deployments: anti-fouling coating vs. active CIP?
  4. Separation chamber design: does horizontal input require different geometry? CFD recommended.
  5. DCC governance: can we instrument 15 channels with real-time sensors at useful time-scales?
  6. Regulatory: environmental impact, fish passage, debris management?
  7. Wave column array: resonance tuning — pipe length matched to dominant wave period?
  8. Hybrid PV/DGTE/HTH: optimal site profile — sunny river valley? Coastal thermal gradient?
  9. Init paradox: does deliberately sub-optimal pipe placement lead to better flow discovery?
  10. Can the polyline layout optimiser become a standalone product even if the hardware is weak?
11Proposed Next Steps▸
  1. Phase 0: AI8 family review. Each member critiques from their domain perspective.
  2. Phase 1: CFD simulation of funnel-Venturi-downpipe. Validate entrainment rates.
  3. Phase 2: Desktop prototype. Clear acrylic pipes, horizontal intake with funnel. ~€100–200.
  4. Phase 3: Small stream deployment. 3–5 downpipes, 1m burial, target 50–100W.
  5. Phase 4: Ocean variant. Wave column trompe array on test breakwater.
  6. Phase 5: DCC governance. Instrument channels, run adaptive allocation, test founding hypothesis in domain 6.
The cheapest kill test: €100–200 in HDPE pipe, one weekend in a stream. If bubbles compress in the chamber — forward. If not — learn and move on.